Important information about NSF’s implementation of the revised 2 CFR

NSF Financial Assistance awards (grants and cooperative agreements) made on or after October 1, 2024, will be subject to the applicable set of award conditions, dated October 1, 2024, available on the NSF website. These terms and conditions are consistent with the revised guidance specified in the OMB Guidance for Federal Financial Assistance published in the Federal Register on April 22, 2024.

Important information for proposers

All proposals must be submitted in accordance with the requirements specified in this funding opportunity and in the NSF Proposal & Award Policies & Procedures Guide (PAPPG) that is in effect for the relevant due date to which the proposal is being submitted. It is the responsibility of the proposer to ensure that the proposal meets these requirements. Submitting a proposal prior to a specified deadline does not negate this requirement.

Dear Colleague Letter

Quantum Manufacturing

Invites Early-concept Grants for Exploratory Research (EAGER) proposals and standard research proposals focused on innovations to enable and accelerate the manufacturing of quantum devices, from device fabrication to potential modes of system integration.

Invites Early-concept Grants for Exploratory Research (EAGER) proposals and standard research proposals focused on innovations to enable and accelerate the manufacturing of quantum devices, from device fabrication to potential modes of system integration.

Dear Colleagues:

The potential of powerful quantum-based computing, sensing, and communications to revolutionize science and technology has been demonstrated in initial functioning quantum systems that enable applications and solutions that are currently impossible using conventional technologies. However, quantum systems, particularly quantum computers, are complex and generally require extreme operating conditions that impact their design, stability, and cost. New approaches to manufacturing quantum devices comprising quantum systems are needed to address the demanding requirements for potential operation at sub-1K temperatures, extreme precision in device fabrication and heterogeneous integration, reproducibility, scalability, packaging, and assembly. Additionally, novel device manufacturing approaches are needed to reduce the system cost of quantum systems to make them widely available.

Presently, there are several quantum platforms under development, and each has its own challenges. Solid-state defect, Si-based spin, topological platforms, superconducting and ion trap-based qubits and platforms all have unique challenges and material issues. Aside from research needs in the discovery and refinement of new quantum-based devices, there is a need for new processes for, and approaches to, the precision integration of new materials in production at scale.

With this Dear Colleague Letter (DCL), the National Science Foundation's (NSF) Directorate for Engineering (ENG) invites the submission of EArly-concept Grants for Exploratory Research (EAGER) proposals or standard research proposals which focus on new manufacturing innovations enabling and accelerating the manufacturing of quantum devices with emphases spanning from device fabrication to potential modes of system integration.

Research addressing scalable processes and process control of interest could address, among other topics:

  • The controlled introduction in all three dimensions of specific defects in diamond and other materials, aligned with their targeted function performance;
  • Deposition of defect-free dielectric and superconducting films with low loss at cryogenic temperatures;
  • Sources of decoherence in spin qubits originating from process-related sources.
  • New methods of large area, high-throughput characterization of quantum-based materials and devices;
  • The exploration of new materials platforms and their fabrication through techniques, such as epitaxial growth enabling pathways to protect and use quantum coherence in solid-state environments;
  • Key processes enabling 3D integration of quantum and traditional electronic, such as high aspect ratio vias and flip chip bump bonding processes;
  • Hybrid integration of quantum devices with photonics for the distribution of quantum information;
  • New approaches to packaging that integrates quantum, photonic, and electronic functions in a vacuum environment; or
  • Approaches towards the automated scalable manufacturing of devices applicable to quantum computers, sensors, and systems.

Proposed research projects that are responsive to this DCL should be based on the close collaboration between experiment and theory, and/or to novel, unconventional, and high-risk/high-reward ideas or strategies to address key scientific challenges in the manufacturing of quantum-based devices. Close collaboration between manufacturing and device scientists is strongly encouraged.

Standard research proposals can be submitted to the programs listed below at any time.

The EAGER type of proposal is described in Chapter II.E.3 of the NSF Proposal & Award Policies & Procedures Guide (PAPPG):

Per the PAPPG, the submission of EAGER proposals is by invitation only; the process is initiated by the submission of a Research Concept Outline (RCO) describing the proposed high–risk / high–reward project that addresses this challenge. The RCO must clearly describe the idea with a clear explanation of why it is exploratory, potentially transformative, or otherwise potentially impactful. RCOs are strictly limited in length to 2 pages, including references, plus a half-page justification of proposed budget, for a total of 2.5 pages. All correspondence, inquiries and RCOs must be via email to one of the Program Directors listed below.

EAGER proposals submitted without prior submission of a corresponding RCO and subsequent invitation will be returned without review. Per the PAPPG, the email invitation from an NSF Program Director serves as documentation of approval to submit an EAGER proposal and must be uploaded in the Supplementary Documentation section of the invited EAGER proposal. The RCO and proposal titles must begin with "EAGER: Quantum Manufacturing:" followed by a brief descriptive title. For consideration by this DCL opportunity, RCOs must be submitted by June 1, 2022, and invited EAGER proposals must be submitted by July 31, 2022.

The following NSF programs are participating in this opportunity and will accept RCOs:

KEY CONTACTS

CMMI: Thomas F. Kuech, tkuech@nsf.gov
ECCS: Rosa Lukaszew, rlukasze@nsf.gov

Sincerely,

Susan Margulies
Assistant Director, Engineering